-- *****************************************************************
-- CISCO-OTN-IF-MIB.my
-- DWDM OTN INTERFACE MIB
--
-- June 2007 Hameed Yasser Shahul (hsahul)
--
-- Copyright (c) 2007 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-OTN-IF-MIB DEFINITIONS::=BEGINIMPORTSInteger32,
Counter32,Unsigned32,Counter64,MODULE-IDENTITY,OBJECT-TYPEFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTION,TruthValue,RowStatus,StorageTypeFROM SNMPv2-TC
ifIndex
FROM IF-MIB
ciscoMgmt
FROM CISCO-SMI;ciscoOtnIfMIB MODULE-IDENTITYLAST-UPDATED"200710100000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-dwdm-mibs@cisco.com"DESCRIPTION"This MIB module defines the managed objects for physical layer
characteristics of DWDM optical channel interfaces and performance
statistics objects for protocol specific error counters in DWDM
optical devices.
Performance monitoring (PM) parameters are used by service
providers to gather, store, set thresholds for and report
performance data for early detection of problems. Thresholds are
used to set error levels for each PM parameter. During the
accumulation cycle, if the current value of a performance
monitoring parameter reaches or exceeds its corresponding threshold
value, a threshold crossing alarm (TCA) is generated. The TCAs
provide early detection of performance degradation.
The definitions contained herein are based on the OTN
specifications in ITU-T G.872[ITU-T G.872], G.709 [ITU-T G.709],
G.798[ITU-T G.798], G.874[ITU-T G.874], and
G.874.1[ITU-T G.874.1].
Glossary:
OTN : Optical Transport Network (ITU-T G.709).
FEC : Forward Error Correction.
PM : Performance Monitor.
DWDM : Dense Wavelength Division Multiplexing.
FE : Farend or client side of the interface.
NE : Nearend or trunk side of the interface.
ADM : Add Drop Multiplexer.
OCH : Optical Channel.
OTS : Optical Transport Section.
OMS : Optical Multiplex Section.
TCA : Threshold Crossing Alarm.
OSC : Optical Supervisory Channel.
DCU : Dispersion Compensation Unit.
EXP : Express Channel.
OSNR : Optical singal to noise ratio. "REVISION"200710100000Z"DESCRIPTION"The initial revision of this MIB."::={ ciscoMgmt 639}-- Textual ConventionsCoiIntervalType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This value indicates the time period over which performance
monitoring data has been collected. Valid values are -
fifteenMin(1) - values for the 15 min interval.
oneDay(2) - values for the 1 Day interval."SYNTAXINTEGER{fifteenMin(1),oneDay(2)}CoiMonitorType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This value indicates the part of the optical network in which the
performance statistics is being monitored. Valid values are -
path(1) - Performance statistics for path parameters.
section(2) - Performance statistics for section parameters.
tcm1(3) - Performance statistics for tandem connection
monitoring 1.
tcm2(4) - Performance statistics for tandem connection
monitoring 2."SYNTAXINTEGER{path(1),section(2),
tcm1(3),tcm2(4)}CoiOtnThresholdType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This value indicates the type of OTN Error Thresholds that can
be defined. Valid values are -
fc(1) - Failure Counts.
es(2) - Errored Seconds.
ses(3) - Severely Errored Seconds.
uas(4) - Unavailable Seconds.
bbe(5) - Bit Block Errors.
esr(6) - Error Seconds Ratio.
sesr(7) - Severely Errored Seconds Ratio.
bber(8) - Background Block Errored Seconds Ratio."REFERENCE"ITU - T Recommendation G.8201 - Error performance parameters
and objectives for multi-operator international paths within
the Optical Transport Network (OTN).
ITU - T Recommendation M.2140: Transport network event
correlation.
ITU - T Recommendation G.826 - End-to-end error performance
parameters and objectives for international constant bit-rate
digital paths and connections."SYNTAXINTEGER{fc(1),
es(2),ses(3),uas(4),bbe(5),esr(6),sesr(7),bber(8)}CoiOpticalWavelength ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This value represents the wavelength of optical signals in a
DWDM optical channel. It is represented in units of picometers.
A value of zero either indicates that the wavelength is unknown,
or that it does not fall under the frequency grid defined in
ITU-T G.694.1"REFERENCE"ITU - T Recommendation G.694.1 - Spectral grids for WDM
applications: DWDM frequency grid, May 2002"SYNTAXUnsigned32(0 | 1528770..1604030)
-- MIB Notification DefinitionsciscoOtnIfMIBNotifs OBJECTIDENTIFIER::={ ciscoOtnIfMIB 0}-- MIB Object DefinitionsciscoOtnIfMIBObjects OBJECTIDENTIFIER::={ ciscoOtnIfMIB 1}coiDwdmInterface OBJECTIDENTIFIER::={ ciscoOtnIfMIBObjects 1}coiDwdmIfOtn OBJECTIDENTIFIER::={ ciscoOtnIfMIBObjects 2}coiDwdmIfFEC OBJECTIDENTIFIER::={ ciscoOtnIfMIBObjects 3}coiIfControllerTable OBJECT-TYPESYNTAXSEQUENCEOF CoiIfControllerEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides management information for physical layer
related attributes of interfaces with an ifType of
opticalChannel(195)."
::={ coiDwdmInterface 1}coiIfControllerEntry OBJECT-TYPESYNTAX CoiIfControllerEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information on physical layer
related attributes of interfaces with an ifType
opticalChannel(195). Entries are created by the agent when a
new interface is added to the ifTable. Entries are deleted by
the agent when an interface is removed from the ifTable."INDEX{ ifIndex }::={ coiIfControllerTable 1}
CoiIfControllerEntry ::=SEQUENCE{
coiIfControllerLoopback INTEGER,
coiIfControllerWavelength CoiOpticalWavelength,
coiIfControllerLaserAdminStatus INTEGER,
coiIfControllerLaserOperStatus INTEGER,
coiIfControllerOtnStatus TruthValue,
coiIfControllerFECMode INTEGER,
coiIfControllerTDCOperMode INTEGER,
coiIfControllerTDCOperStatus INTEGER,
coiIfControllerTDCOperSetting Integer32,
coiIfControllerPreFECBERMantissa Integer32,
coiIfControllerPreFECBERExponent Integer32,
coiIfControllerQFactor Integer32,
coiIfControllerQMargin Integer32,
coiIfControllerOTNValidIntervals Unsigned32,
coiIfControllerFECValidIntervals Unsigned32}coiIfControllerLoopback OBJECT-TYPESYNTAXINTEGER{noLoop(1),otherLoop(2),diagnosticLoop(3),lineLoop(4)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is used to configure the loopback mode of the
interface.
valid values are -
'noLoop' - No Loopback present.
'otherLoop' - A loopback of type other than rest of types
defined in this enumeration.
'diagnosticLoop' - This is an internal loopback, where the
data stream is looped from the transmit
to receive section. It is used for
hardware debug, bring-up and diagnostics.
'lineLoop' - In this mode, the receive data stream is
looped back to the transmit side."DEFVAL{ noLoop }::={ coiIfControllerEntry 1}coiIfControllerWavelength OBJECT-TYPESYNTAX CoiOpticalWavelength
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is used to configure the wavelength of operation on
applicable optical channel interfaces."DEFVAL{1529553}::={ coiIfControllerEntry 2}coiIfControllerLaserAdminStatus OBJECT-TYPESYNTAXINTEGER{up(1),
down(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is used to configure laser status on applicable
interfaces. when it is set to down(2), it results in traffic drop
and there should be corresponding change in
coiIfControllerLaserOperStatus.
Valid values are -
'up' - Turn on the Laser
'down' - shutdown the Laser."DEFVAL{ up }::={ coiIfControllerEntry 3}coiIfControllerLaserOperStatus OBJECT-TYPESYNTAXINTEGER{up(1),down(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the current operational state of the Laser.
Valid values are -
'up' - The laser is operational.
'down' - The laser is not operational.
if coiIfControllerLaserAdminStatus is down(2) then
coiIfControllerLaserOperStatus should be down(2). If
coiIfControllerLaserAdminStatus is changed to up(1) then
coiIfControllerLaserOperStatus should change to up(1), provided
the laser is operational and ready to transmit traffic.
It should remain in down(2) if there is a fault that prevents
it from going to the up(1) state."::={ coiIfControllerEntry 4}coiIfControllerOtnStatus OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object allows the management client to enable
the OTN (ITU-T G.709) framing on applicable interfaces of
ifType opticalChannel(195).
Valid values are -
'true' - Enables OTN (ITU-T g.709) framing on the interface.
'false' - Disables OTN (ITU-T g.709 framing on the interface.
Setting a value of 'false' to coiIfControllerOtnStatus
would result in loss of traffic."DEFVAL{ true }::={ coiIfControllerEntry 5}coiIfControllerFECMode OBJECT-TYPESYNTAXINTEGER{
disable(1),enableStandard(2),enableEnhanced(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object allows the management client to enable
FEC ( Forward Error Correction ) on applicable interfaces.
FEC is a technique that improves digital channel quality
through the addition of redundant data at the sending node.
This redundant data is decoded at the receiver to detect and
correct errors.
Valid values are
'disable' - disables FEC on the interface.
'enableStandard' - enables standard FEC on the interface
(ITU-T G.975).
'enableEnhanced' - enables proprietary FEC on the interface."DEFVAL{ enableEnhanced }::={ coiIfControllerEntry 6}coiIfControllerTDCOperMode OBJECT-TYPESYNTAXINTEGER{auto(1),manual(2)
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the operational mode of the Tuned
Dispersion Compensator (TDC).
The values may be -
'auto' - Automatic tuning of dispersion compensation.
'manual' - Manual tuning of dispersion compensation."::={ coiIfControllerEntry 7}coiIfControllerTDCOperStatus OBJECT-TYPESYNTAXINTEGER{disabled(1),acquiring(2),locked(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the operational status of the Tuned
Dispersion Compensator (TDC).
The values may be -
'disabled' - TDC has been disabled.
'acquiring' - TDC is acquiring or tuning to the desired
compensation setting.
'locked' - TDC has been tuned and locked at the desired
compensation setting"::={ coiIfControllerEntry 8}coiIfControllerTDCOperSetting OBJECT-TYPESYNTAXInteger32(-2000..2000)UNITS"ps/nm - picoseconds per nanometer"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the dispersion compensation setting that the
TDC has been tuned to. It is expressed in pico-seconds per
nanometer.
Example: The value of -650 represents a dispersion compensation
setting of -650 ps/nm."::={ coiIfControllerEntry 9}coiIfControllerPreFECBERMantissa OBJECT-TYPESYNTAXInteger32(0..999)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the mantissa part of the Pre FEC BER or
correctable BER at any instance of time. It is represented in
one hundreths of a unit.The exponent part is defined in
coiIfControllerPreFECBERExponent
Pre FEC BER is the BER of the signal before it undergoes the
FEC algorithm. FEC will correct errors upto a certain
Pre FEC BER beyond which the signal starts becoming
uncorrectable. Knowing the Pre FEC BER helps monitor system
health. Pre FEC BER is expressed in Scientific E notation
with two decimal places
Example: The value 235 represents the mantissa of 2.35"::={ coiIfControllerEntry 10}coiIfControllerPreFECBERExponent OBJECT-TYPESYNTAXInteger32(-30..0)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the exponent part of the Pre FEC BER or
correctable BER at any instance of time. It is represented in
powers of 10. The mantissa part is defined in
coiIfControllerPreFECBERMantissa.
Pre FEC BER is the BER of the signal before it undergoes the
FEC algorithm. FEC will correct errors upto a certain
Pre FEC BER beyond which the signal starts becoming
uncorrectable. Knowing the Pre FEC BER helps monitor system
health. Pre FEC BER is expressed in Scientific E notation with
two decimal places
Example: The value -11 represents the exponent value of 10 to
the power of -11."::={ coiIfControllerEntry 11}coiIfControllerQFactor OBJECT-TYPESYNTAXInteger32(0..9999)UNITS"one hundredths of a dB"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This Object gives the value of Q-Factor represented in one
hundredths of a dB. Q-Factor represents the analog signal to
noise ratio. It suggests the minimum correctable BER for a
given signal. The higher the Q-factor, the better. Q-factor is
expressed in dB
Example: The value 365 represents a Q-Factor of 3.65 dB"::={ coiIfControllerEntry 12}coiIfControllerQMargin OBJECT-TYPESYNTAXInteger32(0..9999)UNITS"one hundredths of a dBQ"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Q-Margin defines how much operational system margin that is
available for a given circuit. Minimum margin should be
defined by one's Network Engineering Group. Q-margin is
expressed in dBQ. dBQ is a scale relative to min required
Q-Factor given by coiIfControllerQFactor.
This object gives the value of the Q-Margin represented in one
hundredths of a dBQ.
Example: The value 236 represents a Q-Margin of 2.36 dBQ."::={ coiIfControllerEntry 13}coiIfControllerOTNValidIntervals OBJECT-TYPESYNTAXUnsigned32(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the number of contiguous 15 minute
intervals for which valid OTN performance monitoring data is
available for the particular interface.
The actual performance data is available in the following
Tables
coiOtnNearEndIntervalTable
coiOtnFarEndIntervalTable
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of 15 minute intervals for which the agent
has some data.
This object reports value zero, if OTN is turned off by
setting coiIfControllerOtnStatus to 'false'."::={ coiIfControllerEntry 14}coiIfControllerFECValidIntervals OBJECT-TYPESYNTAXUnsigned32(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object gives the number of contiguous 15 minute
intervals for which valid FEC PM data is available
for the particular interface.
The actual performance data is available in the following
Table
coiFECIntervalTable
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of 15 minute intervals for which the agent
has some data.
This object reports a value 0, if FEC is disabled by setting
coiIfControllerFECMode to 'disable'."::={ coiIfControllerEntry 15}coiOtnNearEndThresholdsTable OBJECT-TYPE
SYNTAXSEQUENCEOF CoiOtnNearEndThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides objects for configuring OTN ( G.709 )
near end error thresholds on interfaces of ifType
opticalChannel (195)."::={ coiDwdmIfOtn 1}coiOtnNearEndThresholdsEntry OBJECT-TYPESYNTAX CoiOtnNearEndThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information for configuration of
performance monitoring thresholds for a given monitor and
threshold type. Entries can be created for interfaces with
ifType of opticalChannel(195). Thresholds are created/destroyed
through the entry's RowStatus object semantics.
The coiOtnNearEndThreshIntervalType defines the time interval over
which the data being monitored is accumulated for which the
threshold is to be applied.
The coiOtnNearEndThreshMonType defines the type of statistics to
which the threshold applies.
The coiOtnNearEndThresholdType defines the specific threshold type
value, which the threshold refers to."INDEX{
ifIndex,
coiOtnNearEndThreshIntervalType,
coiOtnNearEndThreshMonType,
coiOtnNearEndThresholdType
}::={ coiOtnNearEndThresholdsTable 1}
CoiOtnNearEndThresholdsEntry ::=SEQUENCE{
coiOtnNearEndThreshIntervalType CoiIntervalType,
coiOtnNearEndThreshMonType CoiMonitorType,
coiOtnNearEndThresholdType CoiOtnThresholdType,
coiOtnNearEndThreshValue Unsigned32,
coiOtnNearEndThreshStorageType StorageType,
coiOtnNearEndThreshStatus RowStatus}coiOtnNearEndThreshIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object specifies the interval type during which the
performance statistics were accumulated."::={ coiOtnNearEndThresholdsEntry 1}coiOtnNearEndThreshMonType OBJECT-TYPE
SYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of performance monitoring for which
the threshold is being set."::={ coiOtnNearEndThresholdsEntry 2}coiOtnNearEndThresholdType OBJECT-TYPESYNTAX CoiOtnThresholdType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of Error Threshold that is being
set."::={ coiOtnNearEndThresholdsEntry 3}coiOtnNearEndThreshValue OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to set the near end threshold value for the
given threshold type as identified by coiOtnNearEndThresholdType."::={ coiOtnNearEndThresholdsEntry 4}coiOtnNearEndThreshStorageType OBJECT-TYPE
SYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row."DEFVAL{ nonVolatile }::={ coiOtnNearEndThresholdsEntry 5}coiOtnNearEndThreshStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object controls the creation and deletion of a conceptual
row in this table. The value of this object has no effect on
whether other objects in this conceptual row can be modified.
A conceptual row can not be made active until the
coiOtnNearEndThreshValue has been set to a valid threshold
value."::={ coiOtnNearEndThresholdsEntry 6}coiOtnFarEndThresholdsTable OBJECT-TYPESYNTAXSEQUENCEOF CoiOtnFarEndThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table provides objects for configuring OTN ( G.709 )
thresholds for far end of interfaces of ifType
opticalChannel(195)."::={ coiDwdmIfOtn 2}coiOtnFarEndThresholdsEntry OBJECT-TYPESYNTAX CoiOtnFarEndThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing managment information for configuration of
far end performance monitoring thresholds for a given monitor
and threshold type. Entries can be created for interfaces with
ifType of opticalChannel(195). Thresholds are created/destroyed
through the entry's RowStatus object semantics.
The coiOtnFarEndThreshIntervalType defines the time interval over
which the data being monitored is accumulated for which the
threshold is to be applied.
The coiOtnFarEndThreshMonType defines the type of statistics to
which the threshold applies.
The coiOtnFarEndThresholdType defines the specific threshold type
value, which the threshold refers to."INDEX{
ifIndex,
coiOtnFarEndThreshIntervalType,
coiOtnFarEndThreshMonType,
coiOtnFarEndThresholdType
}::={ coiOtnFarEndThresholdsTable 1}
CoiOtnFarEndThresholdsEntry ::=SEQUENCE{
coiOtnFarEndThreshIntervalType CoiIntervalType,
coiOtnFarEndThreshMonType CoiMonitorType,
coiOtnFarEndThresholdType CoiOtnThresholdType,
coiOtnFarEndThreshValue Unsigned32,
coiOtnFarEndThreshStorageType StorageType,
coiOtnFarEndThreshStatus RowStatus}coiOtnFarEndThreshIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval type during which the
performance statistics were accumulated in the far end of the
interface."::={ coiOtnFarEndThresholdsEntry 1}coiOtnFarEndThreshMonType OBJECT-TYPESYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This object gives specify the type of monitoring for which
threshold is being set on interfaces in the far end of the
interface ."::={ coiOtnFarEndThresholdsEntry 2}coiOtnFarEndThresholdType OBJECT-TYPESYNTAX CoiOtnThresholdType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of Error Threshold that is being
set on far end interfaces of ifType opticalChannel (195)."::={ coiOtnFarEndThresholdsEntry 3}coiOtnFarEndThreshValue OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to set the far end threshold value for
the given threshold type as identified by the index
coiOtnFarEndThresholdType."::={ coiOtnFarEndThresholdsEntry 4}coiOtnFarEndThreshStorageType OBJECT-TYPESYNTAXStorageType
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row."DEFVAL{ nonVolatile }::={ coiOtnFarEndThresholdsEntry 5}coiOtnFarEndThreshStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object controls the creation and deletion of a conceptual
row in this table. The value of this object has no effect on
whether other objects in this conceptual row can be modified.
A conceptual row can not be made active until the
coiOtnFarEndThreshValue has been set to valid threshold value."::={ coiOtnFarEndThresholdsEntry 6}coiOtnNearEndCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF CoiOtnNearEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the cumulative OTN (G.709) PM statistics
for the near end of interfaces of ifType opticalChannel(195).
The statistics are for the current interval of interval type
identified by coiOtnNearEndCurIntervalType. The current
PM statistics is the accumlated statistics for the time
period defined by the interval type."::={ coiDwdmIfOtn 3}coiOtnNearEndCurrentEntry OBJECT-TYPESYNTAX CoiOtnNearEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information on near end
error/statistics counters such as Failure Counts, Errored
Seconds...etc in the current interval"INDEX{
ifIndex,
coiOtnNearEndCurIntervalType,
coiOtnNearEndCurrentMonType
}::={ coiOtnNearEndCurrentTable 1}
CoiOtnNearEndCurrentEntry ::=SEQUENCE{
coiOtnNearEndCurIntervalType CoiIntervalType,
coiOtnNearEndCurrentMonType CoiMonitorType,
coiOtnNearEndCurrentFCs Counter32,
coiOtnNearEndCurrentESs Counter32,
coiOtnNearEndCurrentSESs Counter32,
coiOtnNearEndCurrentUASs Counter32,
coiOtnNearEndCurrentBBEs Counter32,
coiOtnNearEndCurrentESRs Counter32,
coiOtnNearEndCurrentSESRs Counter32,
coiOtnNearEndCurrentBBERs Counter32}coiOtnNearEndCurIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval type during which the
near end performance statistics are accumulated."::={ coiOtnNearEndCurrentEntry 1}coiOtnNearEndCurrentMonType OBJECT-TYPESYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the part of optical network for which
the near end OTN performance statistics are being monitored."::={ coiOtnNearEndCurrentEntry 2}
coiOtnNearEndCurrentFCs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of failures
encountered on the near end of interface in the current
interval of type coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 "::={ coiOtnNearEndCurrentEntry 3}coiOtnNearEndCurrentESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Errored Seconds
encountered on near end of interface in the current
interval of type coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.6.1 "::={ coiOtnNearEndCurrentEntry 4}coiOtnNearEndCurrentSESs OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Severely Errored Seconds
encountered on the near end of interface in the current
interval of type coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.6.2 "::={ coiOtnNearEndCurrentEntry 5}coiOtnNearEndCurrentUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Unavailable Seconds
encountered on the near end of interface in the current
interval of type coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826"::={ coiOtnNearEndCurrentEntry 6}coiOtnNearEndCurrentBBEs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The counter associated with the number of Background Block Errors
encountered on the near end of interface in the current
interval of type coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.5.4 "::={ coiOtnNearEndCurrentEntry 7}coiOtnNearEndCurrentESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Errored Seconds Ratio on the near
end of interface in the current interval of type
coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.7.1"::={ coiOtnNearEndCurrentEntry 8}coiOtnNearEndCurrentSESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Severely Errored Seconds
ratio on the near end of interface in current interval of type
coiOtnNearEndCurIntervalType."
REFERENCE"ITU - T Recommendation G.826 Section 4.7.2 "::={ coiOtnNearEndCurrentEntry 9}coiOtnNearEndCurrentBBERs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Background Block Errors
ratio on the near end of interface in current interval of type
coiOtnNearEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.7.3 "::={ coiOtnNearEndCurrentEntry 10}coiOtnFarEndCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF CoiOtnFarEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the cumulative OTN (G.709) PM stats
for the far end of interfaces of ifType opticalChannel(195).
The statistics are for the current interval of interval type
identified by coiOtnFarEndCurIntervalType. The current
PM statistics is the accumlated statistics for the time
period defined by the interval type."
::={ coiDwdmIfOtn 4}coiOtnFarEndCurrentEntry OBJECT-TYPESYNTAX CoiOtnFarEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing managment information on far end
error/statistics counters such as Failure Counts, Errored
Seconds...etc in the current interval"INDEX{
ifIndex,
coiOtnFarEndCurIntervalType,
coiOtnFarEndCurrentMonType
}::={ coiOtnFarEndCurrentTable 1}
CoiOtnFarEndCurrentEntry ::=SEQUENCE{
coiOtnFarEndCurIntervalType CoiIntervalType,
coiOtnFarEndCurrentMonType CoiMonitorType,
coiOtnFarEndCurrentFCs Counter32,
coiOtnFarEndCurrentESs Counter32,
coiOtnFarEndCurrentSESs Counter32,
coiOtnFarEndCurrentUASs Counter32,
coiOtnFarEndCurrentBBEs Counter32,
coiOtnFarEndCurrentESRs Counter32,
coiOtnFarEndCurrentSESRs Counter32,
coiOtnFarEndCurrentBBERs Counter32}coiOtnFarEndCurIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval type during which the
performance statistics are accumulated in the far end
of the interface."::={ coiOtnFarEndCurrentEntry 1}coiOtnFarEndCurrentMonType OBJECT-TYPESYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the part of optical network for which
far end OTN performance statistics are being monitored."::={ coiOtnFarEndCurrentEntry 2}coiOtnFarEndCurrentFCs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The counter associated with the number of failures
encountered on far end of interface in current interval of
type coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826"::={ coiOtnFarEndCurrentEntry 3}coiOtnFarEndCurrentESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Errored Seconds
encountered on far end of interface in current interval of
type coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.6.1 "::={ coiOtnFarEndCurrentEntry 4}coiOtnFarEndCurrentSESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Severely Errored
Seconds encountered on far end of interface in the current
interval of type coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.6.2 "::={ coiOtnFarEndCurrentEntry 5}coiOtnFarEndCurrentUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Unavailable
Seconds encountered on far end of interface in the current
interval of type coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826"::={ coiOtnFarEndCurrentEntry 6}coiOtnFarEndCurrentBBEs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Background Block
Errors encountered on far end of interface in the current
interval of type coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.5.4 "::={ coiOtnFarEndCurrentEntry 7}
coiOtnFarEndCurrentESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Errored Seconds Ratio
on far end of interface in the current interval of type
coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.7.1 "::={ coiOtnFarEndCurrentEntry 8}coiOtnFarEndCurrentSESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Severely Errored Seconds
ratio on far end of interface in the current interval of type
coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.7.2 "::={ coiOtnFarEndCurrentEntry 9}coiOtnFarEndCurrentBBERs OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Background Block Errors
ratio on far end of interface in the current interval of type
coiOtnFarEndCurIntervalType."REFERENCE"ITU - T Recommendation G.826 Section 4.7.3 "::={ coiOtnFarEndCurrentEntry 10}coiOtnNearEndIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CoiOtnNearEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains historical cumulative OTN (G.709) PM stats
for the near end of interfaces of ifType opticalChannel(195),
for the interval type identified by the index
coiOtnNearEndIntervalType and the interval number as identified
by the index coiOtnNearEndIntervalNum. The PM statistics is the
accumlated stats for the time period defined by the interval
type in the time interval as defined by interval number."::={ coiDwdmIfOtn 5}coiOtnNearEndIntervalEntry OBJECT-TYPESYNTAX CoiOtnNearEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information on near end
error/statistics counters such as Failure Counts, Errored
Seconds...etc in the given interval."INDEX{
ifIndex,
coiOtnNearEndIntervalType,
coiOtnNearEndIntervalMonType,
coiOtnNearEndIntervalNum
}::={ coiOtnNearEndIntervalTable 1}
CoiOtnNearEndIntervalEntry ::=SEQUENCE{
coiOtnNearEndIntervalType CoiIntervalType,
coiOtnNearEndIntervalMonType CoiMonitorType,
coiOtnNearEndIntervalNum Integer32,
coiOtnNearEndIntervalFCs Counter32,
coiOtnNearEndIntervalESs Counter32,
coiOtnNearEndIntervalSESs Counter32,
coiOtnNearEndIntervalUASs Counter32,
coiOtnNearEndIntervalBBEs Counter32,
coiOtnNearEndIntervalESRs Counter32,
coiOtnNearEndIntervalSESRs Counter32,
coiOtnNearEndIntervalBBERs Counter32,
coiOtnNearEndIntervalValidData TruthValue}coiOtnNearEndIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval type during which the
performance statistics are accumulated."::={ coiOtnNearEndIntervalEntry 1}coiOtnNearEndIntervalMonType OBJECT-TYPESYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the part of optical network for which
near end OTN performance statistics are being monitored."::={ coiOtnNearEndIntervalEntry 2}coiOtnNearEndIntervalNum OBJECT-TYPESYNTAXInteger32(1..96)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object identifies the interval for which the set of
near end OTN performance values is available.
The interval identified by 1 is the most recent
15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the
one identified by N-1."::={ coiOtnNearEndIntervalEntry 3}coiOtnNearEndIntervalFCs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of failures encountered on
the near end of interface in the interval identified by
coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826."::={ coiOtnNearEndIntervalEntry 4}coiOtnNearEndIntervalESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The counter associated with the number of Errored Seconds
encountered on the near end of interface in the interval
identified by coiOtnNearEndIntervalType and
coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.6.1"::={ coiOtnNearEndIntervalEntry 5}coiOtnNearEndIntervalSESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Severely Errored Seconds
encountered on the near end of interface in the interval
identified by coiOtnNearEndIntervalType and
coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.6.2"::={ coiOtnNearEndIntervalEntry 6}coiOtnNearEndIntervalUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Unavailable Seconds
encountered on the near end of interface in the interval
identified by coiOtnNearEndIntervalType and
coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826."::={ coiOtnNearEndIntervalEntry 7}coiOtnNearEndIntervalBBEs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Background Block Errors
encountered on the near end of interface in the interval
identified by coiOtnNearEndIntervalType and
coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.5.4"::={ coiOtnNearEndIntervalEntry 8}coiOtnNearEndIntervalESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Errored Seconds Ratio on the near
end of interface in the interval identified by
coiiOtnNearEndIntervalType and coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.7.1"::={ coiOtnNearEndIntervalEntry 9}coiOtnNearEndIntervalSESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Severely Errored Seconds ratio
on the near end of interface in the interval identified by
coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.7.2"::={ coiOtnNearEndIntervalEntry 10}coiOtnNearEndIntervalBBERs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Background Block Errors ratio
on the near end of interface in the interval identified by
coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.7.2"
::={ coiOtnNearEndIntervalEntry 11}coiOtnNearEndIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates if the data for the interval identified by
coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum is valid."::={ coiOtnNearEndIntervalEntry 12}coiOtnFarEndIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CoiOtnFarEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains historical cumulative OTN (G.709) PM stats
for the far end interfaces of ifType opticalChannel(195), for
the interval type identified by the index
coiOtnFarEndIntervalType and the interval number as identified
by coiOtnFarEndIntervalNum. The PM statistics is the accumlated
stats for the time period defined by the interval type in the
time interval as defined by interval number."::={ coiDwdmIfOtn 6}
coiOtnFarEndIntervalEntry OBJECT-TYPESYNTAX CoiOtnFarEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing managment information on far end
error/statistics counters such as Failure Counts, Errored
Seconds...etc in the given interval"INDEX{
ifIndex,
coiOtnFarEndIntervalType,
coiOtnFarEndIntervalMonType,
coiOtnFarEndIntervalNum
}::={ coiOtnFarEndIntervalTable 1}
CoiOtnFarEndIntervalEntry ::=SEQUENCE{
coiOtnFarEndIntervalType CoiIntervalType,
coiOtnFarEndIntervalMonType CoiMonitorType,
coiOtnFarEndIntervalNum Integer32,
coiOtnFarEndIntervalFCs Counter32,
coiOtnFarEndIntervalESs Counter32,
coiOtnFarEndIntervalSESs Counter32,
coiOtnFarEndIntervalUASs Counter32,
coiOtnFarEndIntervalBBEs Counter32,
coiOtnFarEndIntervalESRs Counter32,
coiOtnFarEndIntervalSESRs Counter32,
coiOtnFarEndIntervalBBERs Counter32,
coiOtnFarEndIntervalValidData TruthValue}coiOtnFarEndIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval type during which the
far end performance statistics are accumulated."::={ coiOtnFarEndIntervalEntry 1}coiOtnFarEndIntervalMonType OBJECT-TYPESYNTAX CoiMonitorType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the part of optical network for which
far end OTN performance statistics are being monitored."::={ coiOtnFarEndIntervalEntry 2}coiOtnFarEndIntervalNum OBJECT-TYPE
SYNTAXInteger32(1..96)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object identifies the interval for which the set of
far end OTN performance values for this interface is available.
The interval identified by 1 is the most recent
15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the
one identified by N-1."::={ coiOtnFarEndIntervalEntry 3}coiOtnFarEndIntervalFCs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Failures
encountered on the far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 "::={ coiOtnFarEndIntervalEntry 4}coiOtnFarEndIntervalESs OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Errored Seconds
encountered on far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.6.1"::={ coiOtnFarEndIntervalEntry 5}coiOtnFarEndIntervalSESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Severely Errored Seconds
encountered on far end interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.6.2"::={ coiOtnFarEndIntervalEntry 6}coiOtnFarEndIntervalUASs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The counter associated with the number of Unavailable Seconds
encountered on far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 "::={ coiOtnFarEndIntervalEntry 7}coiOtnFarEndIntervalBBEs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Background Block Errors
encountered on far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.5.4"::={ coiOtnFarEndIntervalEntry 8}coiOtnFarEndIntervalESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Errored Seconds Ratio on far end
of interface in the interval identified by coiOtnFarEndIntervalType
and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.7.1"::={ coiOtnFarEndIntervalEntry 9}coiOtnFarEndIntervalSESRs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Severely Errored Seconds
ratio on far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE"ITU - T Recommendation G.826 Section 4.7.2"::={ coiOtnFarEndIntervalEntry 10}coiOtnFarEndIntervalBBERs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the Background Block Errors
ratio on far end of interface in the interval identified
by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum."REFERENCE
"ITU - T Recommendation G.826 Section 4.7.3"::={ coiOtnFarEndIntervalEntry 11}coiOtnFarEndIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates if the far end data for the interval
identified by coiOtnFarEndIntervalType and
coiOtnFarEndIntervalNum is valid."REFERENCE"ITU - T Recommendation G.826 Section 4.7.2"::={ coiOtnFarEndIntervalEntry 12}-- FECThresholds TablecoiFECThresholdsTable OBJECT-TYPESYNTAXSEQUENCEOF CoiFECThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the configurable thresholds
for FEC ( Forward Error Correction ) statistics."::={ coiDwdmIfFEC 1}coiFECThresholdsEntry OBJECT-TYPE
SYNTAX CoiFECThresholdsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing management information for configuration of
FEC thresholds. Entries can be created for ifIndices with an ifType
of opticalChannel(195). Thresholds are created/destroyed,
through the entry's RowStatus object semantics.
The coiFECThreshIntervalType defines the time interval over
which the data being monitored is accumulated for which the
threshold is to be applied.
The coiFECThreshType defines the specific threshold type value,
which the threshold refers to."INDEX{
ifIndex,
coiFECThreshIntervalType,
coiFECThreshType
}::={ coiFECThresholdsTable 1}
CoiFECThresholdsEntry ::=SEQUENCE{
coiFECThreshIntervalType CoiIntervalType,
coiFECThreshType INTEGER,
coiFECThreshValue Unsigned32,
coiFECThreshStorageType StorageType,
coiFECThreshStatus RowStatus}coiFECThreshIntervalType OBJECT-TYPE
SYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of the interval for which the
thresholds are being set."::={ coiFECThresholdsEntry 1}coiFECThreshType OBJECT-TYPESYNTAXINTEGER{bitErrCor(1),byteErrcor(2),zeroErrDet(3),oneErrDet(4),unCorWords(5)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of the FEC Threshold that is being
set. Valid values are -
bitErrCor(1) : Bit Errors Corrected
byteErrcor(2) : Byte Errors Corrected
zeroErrDet(3) : Zero Bit Errors Detected
oneErrDet(4) : One Bit Errors Detected
unCorWords(5) : Un Correctable Words"REFERENCE"ITU - T Recommendation G.8201 - Error performance parameters
and objectives for multi-operator international paths within
the Optical Transport Network (OTN). ITU - T Recommendation
M.2140: Transport network event correlation."::={ coiFECThresholdsEntry 2}coiFECThreshValue OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used for configuring the FEC threshold
value for the given threshold type."::={ coiFECThresholdsEntry 3}coiFECThreshStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row."DEFVAL{ nonVolatile }::={ coiFECThresholdsEntry 4}
coiFECThreshStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object controls the creation and deletion of a conceptual
row in this table.The RowStatus TC requires that this
DESCRIPTION clause states under which circumstances other
objects in this row can be modified. The value of this object
has no effect on whether other objects in this conceptual row
can be modified.
A conceptual row can not be made active until atleast
coiFECThreshValueLSB has been set to a valid threshold value."::={ coiFECThresholdsEntry 5}-- FEC Current TablecoiFECCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF CoiFECCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the cumulative FEC PM stats
for the interfaces of ifType opticalChannel(195) for the current
interval of interval type identified coiFECCurIntervalType."::={ coiDwdmIfFEC 2}
coiFECCurrentEntry OBJECT-TYPESYNTAX CoiFECCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing managment information on FEC related
error/statistics counters such as Bit Errors Corrected,
Byte Errors Corrected etc in the current interval."INDEX{
ifIndex,
coiFECCurIntervalType
}::={ coiFECCurrentTable 1}
CoiFECCurrentEntry ::=SEQUENCE{
coiFECCurIntervalType CoiIntervalType,
coiFECCurrentCorBitErrs Counter64,
coiFECCurrentCorByteErrs Counter64,
coiFECCurrentDetZeroErrs Counter64,
coiFECCurrentDetOneErrs Counter64,
coiFECCurrentUncorWords Counter64}coiFECCurIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"This object gives the interval type during which the FEC PM
statistics have been collected."::={ coiFECCurrentEntry 1}coiFECCurrentCorBitErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Bit Errors Corrected
on this interface in the current interval of type
coiFECCurIntervalType."::={ coiFECCurrentEntry 2}coiFECCurrentCorByteErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Byte Errors Corrected
on this interface in the current interval of type
coiFECCurIntervalType."::={ coiFECCurrentEntry 3}coiFECCurrentDetZeroErrs OBJECT-TYPESYNTAXCounter64
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of zero bit errors detected
on this interface in the current interval of type
coiFECCurIntervalType."::={ coiFECCurrentEntry 4}coiFECCurrentDetOneErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of one bit errors detected
on this interface in the current interval of type
coiFECCurIntervalType."::={ coiFECCurrentEntry 5}coiFECCurrentUncorWords OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of Uncorrectable Words
encountered on this interface in the current interval of type
coiFECCurIntervalType."::={ coiFECCurrentEntry 6}
-- FEC Interval TablecoiFECIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CoiFECIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains historical cumulative FEC PM stats
for the interfaces of ifType opticalChannel(195), for the
interval type identified by the index coiFECIntervalType and
the interval number as identified by index coiFECIntervalNum.
The PM statistics is the accumlated stats for the time period
defined by the interval type in the time interval as defined by
interval number."::={ coiDwdmIfFEC 3}coiFECIntervalEntry OBJECT-TYPESYNTAX CoiFECIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry containing managment information on FEC
error/statistics counters such as Bit Errors Corrected,
Byte Errors Corrected etc in the given interval."INDEX{
ifIndex,
coiFECIntervalType,
coiFECIntervalNum
}::={ coiFECIntervalTable 1}
CoiFECIntervalEntry ::=SEQUENCE{
coiFECIntervalType CoiIntervalType,
coiFECIntervalNum Integer32,
coiFECIntervalCorBitErrs Counter64,
coiFECIntervalCorByteErrs Counter64,
coiFECIntervalDetZeroErrs Counter64,
coiFECIntervalDetOneErrs Counter64,
coiFECIntervalUncorWords Counter64,
coiFECIntervalValidData TruthValue}coiFECIntervalType OBJECT-TYPESYNTAX CoiIntervalType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the type of interval for which the FEC values
have been collected."::={ coiFECIntervalEntry 1}coiFECIntervalNum OBJECT-TYPESYNTAXInteger32(1..96)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object gives the interval for which the set of FEC PM
values are available.
The interval identified by 1 is the most recent
15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the one
identified by N-1."::={ coiFECIntervalEntry 2}coiFECIntervalCorBitErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of
Bit Errors Corrected in the interval identified by
coiFECIntervalType and coiFECIntervalNum."::={ coiFECIntervalEntry 3}coiFECIntervalCorByteErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The counter associated with the number of
Byte Errors Corrected
on this interface in the interval identified by
coiFECIntervalType and coiFECIntervalNum."::={ coiFECIntervalEntry 4}coiFECIntervalDetZeroErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of
zero bit errors detected
on this interface in the interval identified by
coiFECIntervalType and coiFECIntervalNum."::={ coiFECIntervalEntry 5}coiFECIntervalDetOneErrs OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of
one bit errors detected
on this interface in the interval identified by
coiFECIntervalType and coiFECIntervalNum."::={ coiFECIntervalEntry 6}coiFECIntervalUncorWords OBJECT-TYPESYNTAXCounter64
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter associated with the number of
Uncorrectable Words encountered
on this interface in the interval identified by
coiFECIntervalType and coiFECIntervalNum."::={ coiFECIntervalEntry 7}coiFECIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates whether the data for the interval identified
by coiFECIntervalType and coiFECIntervalNum is valid."::={ coiFECIntervalEntry 8}-- MIB Conformance StatementsciscoOtnIfMIBConformance OBJECTIDENTIFIER::={ ciscoOtnIfMIB 2}ciscoOtnIfMIBCompliances OBJECTIDENTIFIER::={ ciscoOtnIfMIBConformance 1}ciscoOtnIfMIBGroups OBJECTIDENTIFIER
::={ ciscoOtnIfMIBConformance 2}ciscoOtnIfMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for platforms that monitor the
operating status and FEC/OTN with respect to error
counters, for the physical layer."MODULE-- this moduleMANDATORY-GROUPS{
coiIfControllerGroup,
coiIfOtnGroup,
coiIfFECGroup
}GROUP coiIfOtnNearEndCurrentGroup
DESCRIPTION"The collection of objects used for monitoring the near end
OTN error counters in the current interval."GROUP coiIfOtnNearEndIntervalGroup
DESCRIPTION"The collection of objects used for monitoring the near end
OTN error counters in a given interval."GROUP coiIfOtnFarEndCurrentGroup
DESCRIPTION"The collection of objects used for monitoring the far end
OTN error counters in the current interval."GROUP coiIfOtnFarEndIntervalGroup
DESCRIPTION"The collection of objects used for monitoring the far end
OTN error counters in a given interval."GROUP coiIfFECCurrentGroup
DESCRIPTION"The collection of objects used for monitoring the FEC error
counters in the current interval."GROUP coiIfFECIntervalGroup
DESCRIPTION"The collection of objects used for monitoring the FEC error
counters in a given interval."OBJECT coiIfControllerLoopback
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiIfControllerWavelength
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiIfControllerOtnStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiIfControllerLaserAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiOtnNearEndThreshValue
MIN-ACCESSread-only
DESCRIPTION"Write access is not required."OBJECT coiOtnNearEndThreshStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiOtnFarEndThreshValue
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiOtnFarEndThreshStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiFECThreshValue
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT coiFECThreshStorageType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ ciscoOtnIfMIBCompliances 1}-- units of conformancecoiIfControllerGroup OBJECT-GROUPOBJECTS{
coiIfControllerLoopback,
coiIfControllerWavelength,
coiIfControllerLaserAdminStatus,
coiIfControllerLaserOperStatus,
coiIfControllerOtnStatus,
coiIfControllerFECMode,
coiIfControllerTDCOperMode,
coiIfControllerTDCOperStatus,
coiIfControllerTDCOperSetting,
coiIfControllerPreFECBERMantissa,
coiIfControllerPreFECBERExponent,
coiIfControllerQFactor,
coiIfControllerQMargin,
coiIfControllerOTNValidIntervals,
coiIfControllerFECValidIntervals
}STATUScurrentDESCRIPTION"The collection of objects to allow configurations and give
information related to the physical layer characteristics
for interfaces of ifType opticalChannel(195)."::={ ciscoOtnIfMIBGroups 1}coiIfOtnNearEndCurrentGroup OBJECT-GROUPOBJECTS{
coiOtnNearEndThreshValue,
coiOtnNearEndThreshStorageType,
coiOtnNearEndThreshStatus,
coiOtnNearEndCurrentFCs,
coiOtnNearEndCurrentESs,
coiOtnNearEndCurrentSESs,
coiOtnNearEndCurrentUASs,
coiOtnNearEndCurrentBBEs,
coiOtnNearEndCurrentESRs,
coiOtnNearEndCurrentSESRs,
coiOtnNearEndCurrentBBERs
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the near end
OTN error counters in the current interval."::={ ciscoOtnIfMIBGroups 3}coiIfOtnNearEndIntervalGroup OBJECT-GROUPOBJECTS{
coiOtnNearEndThreshValue,
coiOtnNearEndThreshStorageType,
coiOtnNearEndThreshStatus,
coiOtnNearEndIntervalFCs,
coiOtnNearEndIntervalESs,
coiOtnNearEndIntervalSESs,
coiOtnNearEndIntervalUASs,
coiOtnNearEndIntervalBBEs,
coiOtnNearEndIntervalESRs,
coiOtnNearEndIntervalSESRs,
coiOtnNearEndIntervalBBERs,
coiOtnNearEndIntervalValidData
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the near end
OTN error counters in a given interval."::={ ciscoOtnIfMIBGroups 4}coiIfOtnFarEndCurrentGroup OBJECT-GROUPOBJECTS{
coiOtnFarEndThreshValue,
coiOtnFarEndThreshStorageType,
coiOtnFarEndThreshStatus,
coiOtnFarEndCurrentFCs,
coiOtnFarEndCurrentESs,
coiOtnFarEndCurrentSESs,
coiOtnFarEndCurrentUASs,
coiOtnFarEndCurrentBBEs,
coiOtnFarEndCurrentESRs,
coiOtnFarEndCurrentSESRs,
coiOtnFarEndCurrentBBERs
}STATUScurrent
DESCRIPTION"The collection of objects used for monitoring the far end
OTN error counters in the current interval."::={ ciscoOtnIfMIBGroups 5}coiIfOtnFarEndIntervalGroup OBJECT-GROUPOBJECTS{
coiOtnFarEndThreshValue,
coiOtnFarEndThreshStorageType,
coiOtnFarEndThreshStatus,
coiOtnFarEndIntervalFCs,
coiOtnFarEndIntervalESs,
coiOtnFarEndIntervalSESs,
coiOtnFarEndIntervalUASs,
coiOtnFarEndIntervalBBEs,
coiOtnFarEndIntervalESRs,
coiOtnFarEndIntervalSESRs,
coiOtnFarEndIntervalBBERs,
coiOtnFarEndIntervalValidData
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the far end
OTN error counters in a given interval."::={ ciscoOtnIfMIBGroups 6}coiIfOtnGroup OBJECT-GROUP
OBJECTS{
coiOtnNearEndThreshValue,
coiOtnNearEndThreshStorageType,
coiOtnNearEndThreshStatus,
coiOtnNearEndCurrentFCs,
coiOtnNearEndCurrentESs,
coiOtnNearEndCurrentSESs,
coiOtnNearEndCurrentUASs,
coiOtnNearEndCurrentBBEs,
coiOtnNearEndCurrentESRs,
coiOtnNearEndCurrentSESRs,
coiOtnNearEndCurrentBBERs,
coiOtnNearEndIntervalFCs,
coiOtnNearEndIntervalESs,
coiOtnNearEndIntervalSESs,
coiOtnNearEndIntervalUASs,
coiOtnNearEndIntervalBBEs,
coiOtnNearEndIntervalESRs,
coiOtnNearEndIntervalSESRs,
coiOtnNearEndIntervalBBERs,
coiOtnNearEndIntervalValidData,
coiOtnFarEndThreshValue,
coiOtnFarEndThreshStorageType,
coiOtnFarEndThreshStatus,
coiOtnFarEndCurrentFCs,
coiOtnFarEndCurrentESs,
coiOtnFarEndCurrentSESs,
coiOtnFarEndCurrentUASs,
coiOtnFarEndCurrentBBEs,
coiOtnFarEndCurrentESRs,
coiOtnFarEndCurrentSESRs,
coiOtnFarEndCurrentBBERs,
coiOtnFarEndIntervalFCs,
coiOtnFarEndIntervalESs,
coiOtnFarEndIntervalSESs,
coiOtnFarEndIntervalUASs,
coiOtnFarEndIntervalBBEs,
coiOtnFarEndIntervalESRs,
coiOtnFarEndIntervalSESRs,
coiOtnFarEndIntervalBBERs,
coiOtnFarEndIntervalValidData
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the OTN error
counters."::={ ciscoOtnIfMIBGroups 7}coiIfFECGroup OBJECT-GROUPOBJECTS{
coiFECThreshValue,
coiFECThreshStorageType,
coiFECThreshStatus,
coiFECCurrentCorBitErrs,
coiFECCurrentCorByteErrs,
coiFECCurrentDetZeroErrs,
coiFECCurrentDetOneErrs,
coiFECCurrentUncorWords,
coiFECIntervalCorBitErrs,
coiFECIntervalCorByteErrs,
coiFECIntervalDetZeroErrs,
coiFECIntervalDetOneErrs,
coiFECIntervalUncorWords,
coiFECIntervalValidData
}STATUScurrentDESCRIPTION"The collection objects used for monitoring the FEC error
counters."::={ ciscoOtnIfMIBGroups 8}coiIfFECCurrentGroup OBJECT-GROUPOBJECTS{
coiFECThreshValue,
coiFECThreshStorageType,
coiFECThreshStatus,
coiFECCurrentCorBitErrs,
coiFECCurrentCorByteErrs,
coiFECCurrentDetZeroErrs,
coiFECCurrentDetOneErrs,
coiFECCurrentUncorWords
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the FEC error
counters in the current interval."::={ ciscoOtnIfMIBGroups 9}coiIfFECIntervalGroup OBJECT-GROUPOBJECTS{
coiFECThreshValue,
coiFECThreshStorageType,
coiFECThreshStatus,
coiFECIntervalCorBitErrs,
coiFECIntervalCorByteErrs,
coiFECIntervalDetZeroErrs,
coiFECIntervalDetOneErrs,
coiFECIntervalUncorWords,
coiFECIntervalValidData
}STATUScurrentDESCRIPTION"The collection of objects used for monitoring the FEC error
counters in a given interval ."::={ ciscoOtnIfMIBGroups 10}
END